Wyszukaj na stronie

Gelcoat White

Gelcoat based on IZO/NPG resin, thanks to which it achieves good resistance to weather conditions and high mechanical properties. Primarily recommended for repairing minor scratches and for the production of laminate products.

The product is delivered without hardener, you need Metox 30. The gelcoat and the catalyst should be mixed gently.

ColorWeightCode
RAL 9010 white1kg300010262
RAL 9010 white250g300010263
METOX 3020 ml300010282
Paraffin corrector60 ml300010264
Gelcoat White

Color

  • white

Application method

Manually:

  • brush

Product description "Gelcoat White"

It is a gelcoat in RAL 9010 color for versatile use:

  • It is useful both in construction and during repairs of damaged boat elements.
  • It is recommended primarily for lamination.
  • In combination with paraffin corrector, it is used to repair minor scratches.
  • Component A is white, and the hardener is Metox 30 liquid.
  • Mixing proportions of the ingredients “gelcoat”: hardener 100:3.

Important

The package contains only gelcoat.
The hardener and paraffin corrector must be purchased separately.

Basic information

Surfacelaminat,
Placeabove and below water line
Functionlaminating, small repairs
Number of Coatsaccording need
Pot Life15-25 min in temperature 20°C
Hardening time24 h in temperature  around 20°C
Colorwhite RAL 9010

Surface preparation

How to use:

First of all, the surface should be degreased and sanded with sandpaper. Remove dust and degrease again.

Mix the base with the hardener in a ratio of 100:3. The gelling time, the so-called potlife, i.e. the possibility of use after mixing the components, is approximately 15-25 minutes at a temperature of approximately 20°C.

Further work:

As already mentioned, the gelcoat undergoes oxygen inhibition under the influence of oxygen (it does not dry out, the surface is always sticky). Assuming that in the case of repairs we use the so-called Topcoat can be achieved by adding paraffin concealer. Recommended amount of paraffin corrector 2%-5%.

You have questions about the product - Gelcoat White

    Gelcoat do laminowania i napraw

    Gelcoat do laminowania i napraw

    Gelcoat do laminowania i napraw

    Also check

    Our FAQ answers to frequently asked questions

    Why despite the use of antifouing paint the bottom of the boat is overgrown?

    Possible causes

    • Too thin layer of antifouling paint,
    • Choosing the wrong antifouling to type of a boat or yacht
    • Thinning of antifouling paint,
    • Incorrect surface preparation before antifouling application.

    How to prevent

    • Apply the right layer thickness of paint indicated by manufacturer,
    • Choose antifouling dedicated to type of boat or yacht and suitable for the type of water,
    • Do not thin antifouling because of the risk of reducing effectiveness,
    • Careful surface preparations (grinding, clearing, degreasing),

    How to remove

    • Wet grinding, apply new layers of antifouling paint.
    • Use C1 shell and fouling remover.

    Can I use universal thinner?

    We do not recommend using universal thinners. The use of a thinner with an unknown composition may result in loss of adhesion, lack of proper flow of paint and varnish defects.

    Why the resin does not harden?

    Possible causes

    • Too low temperature of ambitne,
    • Incorrect proportion of base and herdener,
    • Mixing two components from two different manufacturers

    How to prevent

    • Apply the correct proportions of components
    • Maintain steady temperature (around 20ﹾC) during whole hardening process,
    • Mix the products thoroughly and bleed the mixture.

    How to remove

    • The uncured mass requires complete removal from the surface.
    Wyjście
    Przeiń na górę