Γλώσσα:

MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER

Ιστοσελίδα » Προϊόντα » Στρωτήρες » MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER
Sea-Line
MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER

EPOXY PRIMER MULTIFUNCTIONAL 2K SPRAY

PRODUCT DISCRIPTION:



BASIC INFORMATION:

SurfacesGRP, laminates, steel, aluminum
AreaAbove and below waterline
FunctionGrounding
Intercoating
Filling
Antiosmotic
Anticorosive
Applicationspray can
Theoretical coverage for 400 ml 1-2 м2
Number of coats2 – 4
Pot life 20°C48 h
Time between layers without sanding5~10 minutes
Color (matt)white
Pack400 ml
Code 38758

APPLICATION INSTRUCTION:

potrzasnij

Before triggering, shake can thoroughly for 2 minutes after agitation balls are heard.

spray 2K - korek

Remove the red pushbutton from the cap.
Turn the can by 180° and fit the pushbutton onto the pin in the base of the can.

spray 2K - wcisnij korek

Turn the can upside down and place on a firm surface.
Press the red pushbutton all the way in with the palm of your hand.

potrzasnijAfter triggering, shake can again thoroughly for 2 minutes after agitation balls are heard.

spray 2K - ustaw dysze

Set the adjustable spray nozzle to the size of the damage and damage pattern.

spray 2K - aplikacja

Spray distance: 10 ~ 20cm.

spray 2K - ilosc warstw

Standard application: approx. 2÷4 spray coats, recommended dry film layer: 80 ~200 μm
NOTICE: For antiosmosis and anticorrosion protection recommended DTF is 240 μm.

spray 2K - czas

Allow a flash-off time of approx. 5-10 minutes between spray coats.

spray 2K - oczysc

After painting, turn the can upside down and spray the valve until empty.

spray 2K - utylizacja

The completely empty spray cans can be disposed of in the recycling waste container.
Cans with hardened material must be disposed of as special waste.

TECHNICAL INFORMATION:


Μετοχή:

Έχετε ερωτήσεις;
Θα απαντήσουμε το συντομότερο δυνατό

Σχετικά προϊόντα

από MULTIFUNCTIONAL 2K SPRAY EPOXY PRIMER


Δείτε επίσης
Άλλα προϊόντα αυτής της κατηγορίας

Οι συχνές ερωτήσεις μας
Απαντήσεις σε συνήθεις ερωτήσεις

Contamination in topcoat paint?

Possible causes

  • Inaccurate surface cleaning before paint application,
  • Incorrect painting tools preparation (brush and roll),
  • Performing work in a place exposed to constant contact with dust.

How to prevent

  • Careful surface preparation (grinding, clearing, degreasing),
  • Careful painting tools preparation before use,
  • Maintain clean work environment

How to remove

  • Grind, clean and paint again.

Why the epoxy filler does not harden?

Possible causes

  • Incorrect proportion of base and herdener,
  • Too low temperature of ambient and surface (less than 10ﹾC),
  • Mixing two components from two different manufacturers,

How to prevent

  • Apply the correct proportions of components
  • Maintain steady temperature (around 20ﹾC) during the whole hardening process,
  • Use base and hardener from the same manufacturer

How to remove

  • The uncured mass requires complete removal from the surface.

Can I paint the bottom of the boat with polyurethane paint?

Yes, you can paint the bottom of the boat with polyurethane paint due to its high mechanical strength. We recommend this solution when the boat is not launched for a long time and is not exposed to fouling.

Η προσφορά μας
Εξοικειωθείτε με την προσφορά μας σε υλικά και χρώματα ναυπήγησης σκαφών
Exit
Przewiń na górę