PRODUCT DISCRIPTION:
| Surfaces | GRP, laminates, steel, aluminum | |
| Area | Above and below waterline | |
| Function | Grounding Intercoating Filling Antiosmotic Anticorosive | |
| Application | spray can | |
| Theoretical coverage for 400 ml | 1-2 м2 | |
| Number of coats | 2 – 4 | |
| Pot life 20°C | 48 h | |
| Time between layers without sanding | 5~10 minutes | |
| Color (matt) | white | |
| Pack | 400 ml | |
| Code | 38758 | |
Before triggering, shake can thoroughly for 2 minutes after agitation balls are heard.
Remove the red pushbutton from the cap.
Turn the can by 180° and fit the pushbutton onto the pin in the base of the can.
Turn the can upside down and place on a firm surface.
Press the red pushbutton all the way in with the palm of your hand.
After triggering, shake can again thoroughly for 2 minutes after agitation balls are heard.
Set the adjustable spray nozzle to the size of the damage and damage pattern.
Spray distance: 10 ~ 20cm.
Standard application: approx. 2÷4 spray coats, recommended dry film layer: 80 ~200 μm
NOTICE: For antiosmosis and anticorrosion protection recommended DTF is 240 μm.
Allow a flash-off time of approx. 5-10 minutes between spray coats.
After painting, turn the can upside down and spray the valve until empty.
The completely empty spray cans can be disposed of in the recycling waste container.
Cans with hardened material must be disposed of as special waste.
NASTRO DA MASCHERATURA NASTRO DA MASCHERATURA RESISTENTE ALL’ACQUA NASTRO ARGENTO – SPECIALE NASTRO DA MASCHERATURA DESCRIZIONE DEL PRODOTTO: Con buona […]
MASCHERINA GUANTI MONOUSO IN NITRILE “MASTER” GUANTI MONOUSO IN NITRILE WORKWEAR – SINGLE USE POLYESTER WORKWEAR (blue) reusable overall PASTE […]
TAMPONI PER CARTEGGIATURA – sughero naturale TAMPONI PER CARTEGGIATURA – schluma di sughero TELO PROTETTIVO ROTOLO ASCIUGATUTTO PANNI ANTISTATICI TAMPONI […]
PRIMER EPOSSIDICO LIGHTPRIMER 5:1 DESCRIZIONE DEL PRODOTTO: primer bicomponente di alta qualità per applicazioni sottili ottimo primer per vernici e […]
It is very important to use paint thinners, which provide the appropriate parameters of paint – flow, pot life, time […]
1-component chlorinated rubber primer Recommended above and under the water line It can be use on GRP, steel and wood […]
Yes, you can paint the bottom of the boat with polyurethane paint due to its high mechanical strength. We recommend this solution when the boat is not launched for a long time and is not exposed to fouling.
No, polyurethane is a 2-component paint (base + hardener) and after applying 2-component paint to 1-component paint, the proper adhesion of the paint to the surface will not be maintained, the paint will begin to wrinkle and surface defects will appear.
We recommend to always sand the surface between applying two different products to ensure uniform surface roughness and adhesion of subsequent layers. The sanded surface should also be cleaned and degreased.
Il patch e compensare le irregolarità derivanti da danni durante la produzione
Barca protezione superficiale contro l’influenza di azioni distruttive di osmosi e la corrosione in ambienti difficili
Protezione contro l’acqua e contro gli effetti negativi delle radiazioni UV
Proteggere la parte inferiore della barca prima-tedesco ricoperta di alghe e conchiglie. La prevenzione dell’azione di acqua.
Rimozione efficace di ritenzione graffi, di aggiornamento e il colore del mantello gel o lacca
Laminazione, incollaggio e tappatura perdite
Per il riempimento di piccole fessure e ubyt gemme in gelcoat
Una gamma di prodotti utili quando si lavora costruttore di barche
